The Ultra Series slide offers the longest stroke of any competitive slide of its type.
Bores up to 1-1/16 or 25 mm.
Strokes up to 6 inches or 160mm.
Stroke adjust & shock absorbers.
Dual bearing blocks standard on long strokes.
Fittings installed with a variety of tube options.
Sensing track located on both sides of the Ultra Series.
The PST Series provides smooth precise linear motion with high accuracy at twice the thrust of a single bore cylinder. The precision linear rail system supports the load through the entire stroke length.
Available in 8, 12, 16, 20, 25 mm bore sizes.
Dual square rails provide high load capabilities and precise linear motion.
Twin bores deliver twice the thrust of a single bore cylinder.
Optional stroke adjustment available for extend stroke.
Axial mounting and locating holes standard.
Sensing groove for Hall or Reed switches.
The PS series is a compact lightweight unit with a replaceable air cylinder. Floating piston rod coupling eliminates cylinder binding. Units are permanently lubricated for non-lube air operation, allowing for OSHA compliance. Aluminum body and end blocks contain tapped holes and dowel pin holes for precision mounting or fixturing. Standard end plate to stop shaft vibrations.
Body: Anodized aluminum for reduced weight with multiple mounting surfaces with dowel location holes. Compact size for added space savings
Air Cylinder: Standard stainless steel body and rod for corrosion resistance and permanently lubricated for non-lube service.
Alignment Coupler: Isolates piston rod from side loading, increasing service life.
Optional Shock Absorbers: Recommended for high cycle applications to absorb shock loading, and provides end of stroke adjustment.
Optional Proximity Switch Sensing: For applications requiring end of stroke verification, available for extend and retract positions.
Rear Tooling Plate: Dampens guide rod vibration for smooth operation, and houses shock absorber for extend position.
Bearings: Four recirculating linear ball bearing for maximum load capacity that are sealed from contamination. Self-aligning for maximum guide rod support.
Guide Rods: Hardened steel to Rc60-65, precision ground and polished.
The PBS Series is designed for applications where space is at a minimum. It has an internally built-in air cylinder in the carriage assembly, reducing overall length. The carriage assembly is supported by four recirculating linear ball bearings and two hardened guide shafts.
Carriage: Four recirculating linear ball bearings. Easy access mounting and dowel location holes
Air Cylinder: Internally housed in carriage. Low friction U-cup lip seals for long service life
Tooling Plate: Standard dowel locating holes and accurately milled locating slots. Machined to accept industry standard shock absorbers, and position proximity switch sensors.
Stroke Adjustment: Easy access stroke adjusting screws for exact carriage stroke. Adjustable in both directions
Guide Shafts: Hardened Steel to RC 60-65,
Bearings: Four linear ball bearings...greatest load capacity, factory lubricated, built-in wipers, self-aligning. Four Frelon®, compounded Teflon®...self-lubricating, self-aligning, long service life, ideal for clean room applications.
The B series design is compact and self-contained. Cylinder pistons are attached directly to each guide rod, conserving size without sacrificing output force. Guide rods are supported by specially designed guide bushings providing optimum support of dynamic loads. Guide bushings are manufactured from specially engineered materials designed to eliminate potential rod binding.
Body: Hardcoat anodized aluminum, teflon coated, integrated switch mounting.
Tooling Plate:Universal mounting pattern with standard dowel locating holes.
Guide Shafts: Hardened Steel, (stainless available), large diameters for increased load capability.
Bearings: Low friction, superior rod diameter to bearing length ratio.
Position Sensing: Easy access position sensor mounting.
Bore Size: 7/16", 5/8", 7/8".
The SPS series small size makes it the ideal slide for getting into those tight spaces.
Body: Hardcoat Anodized, Teflon impregnated inside & out.
Slide: Aluminum Bronze alloy, payload can be attached to top of slide or tooling plate.
Stroke Adjustment: Fine adjustments can be made to the extend and retract stroke.
Bearings: Engineered material designed for maximum rigidity, with low friction for long life
Position Sensing: Hall effect sensing is available for both extend and retract stroke
The GS Series Gantry Slide is designed to handle heavier loads and travel greater distances. The design centers around a moving carriage between two fixed tool bars. The carriage is supported and guided by four bearings and two hardened guide shafts.
Carriage: Hardcoat Anodized, patented Numate™ mounting system, direct mounting for slides, grippers and gantries.
Tooling Plate: Precision machined with easy access mounting holes for tooling attachments.
Rod Wipers: Steel reinforced wipers assure protection of bearings from enviroment contamination.
Bearings: Choice between recirculating ball for heavy duty applications and sintered bronze for medium to light duty applications.
Guide Shafts: Hardened ground and polished, oversize diameter for load support and rigidity.
Piston: Internal to body, magnetic band for position sensing.
Sensor Mounting Track: Extruded into the body, no external brackets necessary, hall effect or reed switches.
Bore Size: 16mm, 20mm, 25mm, 32mm, 40mm, 50mm.
The RG Series design centers around two separate systems. The gantry, a guided and supported bearing system, to support the load and the rodless cylinder to drive the gantry carriage.
Carriage: Hardcoat Anodized, patented Numate™ mounting system, direct mounting for Sh , B and LC series slides.
Numatics Rodless Cylinder: Extruded barrel for increased rigidity, Kevlar re-inforced seal strips, cushioned at both ends.
Alignment Coupler: Eliminates side-loading of the cylinder.
Tooling Plate: Easy access mounting, accurate dowel location, accepts shocks.
Guide Shafts: Hardened ground and polished, oversize diameter for load support and rigidity, corrosion resistant available
Bearings: Self lubricating, built in wiper seals, Frelon teflon coated available.
Bore Size: 25mm, 32mm, 40mm, 50mm.